Load and condition
Load a representative product and establish stable hopper presentation without bridging or excessive aeration.
Model guide
Lancing LU-FM710 weigh-assisted auger filler.
A semi-automatic powder filler for operator-presented bottles, jars, tubs and supported bags, with programmed auger dosing and a separate weighing device.
25 L hopper10–2000 g nominal rangeWeigh-assisted optionShort batches
Verified Lancing model
Servo auger dosing with operator-presented packs and weigh checking.
The LU-FM710 is a semi-automatic auger filler for short campaigns and flexible pack formats. The operator presents the bottle, jar, tub or supported bag, starts the cycle and can use the separate weighing device to confirm or refine the result.
- 25 litre agitated hopper
- Programmed auger dosing or weight-assisted operation
- One product-matched auger and nozzle set per approved duty
- Adjustable filling support for the agreed pack range
- Local dust-capture connection for customer extraction
Documented configuration
LU-FM710 technical basis.
These values come from a Lancing quotation configuration. Final suitability, output and acceptance limits remain dependent on the actual powder, tooling, container and trial method.
| Item | Documented basis | Condition to confirm |
|---|---|---|
| Filling method | Programmed auger dose or scale-assisted filling. | Choose the operating mode from the required throughput and weight-control method. |
| Nominal filling range | 10–2000 g with matched tooling. | Dependent on auger, bulk density and pack opening. |
| Hopper | Approximately 25 L with agitation. | Agitator and refill method must suit the product’s flow and bridging tendency. |
| Pack envelope | Bottles or tubs approximately 25–150 mm diameter and 60–300 mm high in the documented configuration; bags require suitable support. | Confirm every pack sample and opening before tooling release. |
| Output basis | Approximately 1–30 containers/minute. | Depends on dose, product flow, weighing mode and operator handling; not a universal guaranteed rate. |
| Accuracy basis | Typically around ±1% after calibration with a stable product. | Final limits must be agreed and proven with representative product, pack, scale and run conditions. |
| Utilities | 220–240 V, 50 Hz, single phase; approximately 1.25 kW. | Confirm final build and site supply before installation. |
| Approximate dimensions | Main unit 450 × 650 × 1860 mm; weighing device 265 × 265 × 570 mm. | Allow operating, cleaning, access and extraction space around the equipment. |
Operating sequence
How the weigh-assisted route works.
Select recipe
Choose the validated auger speed, revolution count, delays and operating mode.
Present the pack
Position the approved pack beneath the outlet at the agreed filling height.
Dispense
The auger meters the programmed dose; the operator removes the pack when the cycle is complete.
Check weight
Use the weighing device for calibration, production sampling or weight-assisted correction as agreed.
Release or adjust
Accept the fill against the sampling plan or correct the recipe before continuing.
Best fit
Use the LU-FM710 where flexibility matters more than automatic pack transport.
The format is well suited to lower-volume production, frequent product or pack changes and development work where an operator remains available. It is not a premade-pouch feeder, bottle indexer or automatic sealing system.
For a larger dose range with a 50 litre hopper, compare the LU-FM750F semi-automatic auger filler. For conveyor-indexed bottles, review the LU-FM4A automatic auger filler.
Send for confirmation
- Representative powder and SDS where applicable
- Minimum and maximum fill weights
- Actual packs and smallest opening
- Required sampling and tolerance method
- Cleaning and changeover expectations
Evidence before order
Trial the product, pack and weighing method together.
Use the powder sample trial and FAT guide to define the test sequence, and the cleaning and changeover guide to review product-contact access. Combustible or otherwise hazardous powders require a separate site- and product-specific assessment before specification.
LU-FM710 enquiry
Request a model reviewSend the powder, fill range and real packs.
Lancing can confirm whether the LU-FM710, its tooling and its weighing approach are suitable for the proposed production method.